POLYURETHANE TEXTURIZED ENAMEL

POLYURETHANE TEXTURIZED ENAMEL

FOR TINTING SYSTEM USE. Two component polyurethane enamel providing a semi-gloss texturized finish for application as a topcoat for boats and for industrial machineries. Thanks to its texturized finish allows to hide uneven surface or irregularities which can be present on the surface. Resistant to agressive environment.

Brand : SKIPPER'S LINE MARINE PAINTS
Description

SURFACE PREPARATION AND APPLICATION

Bare Steel. Onto sandblasted steel according to SA 2,5 apply two coats of EPOZINC 2C or EPOFOND AM-9. If sandblasting would not be possible degrease the surface and remove any trace of corrosion providing a suitable anchor pattern. Any loose paint should be meccanically removed. Apply 2 coats of EPOFOND AM-9 primer and let dry. Fill up if necessary with PLAMUR FINISHER LIGHT. Apply then one coat of POLIFOND primer, let dry for 24 hours and sandpaper. Overcoat with 2 coats of  POLYURETHANE TEXTURIZED ENAMEL allowing 18-24 hours between coats.
 
Fibreglass. 
The surface to be coated should be degreased with suitable cleaner, rinsed and slightly sanded with fine abrasive paper. Remove dust and clean the surface. If the surface is slightly powdering it is necessary to apply one coat of POLIFIBER PRIMER allowing 18-24 hours between coats. Fill up if necessary with PLAMUR FINISHER LIGHT. Overcoat with 2 coats of  POLYURETHANE TEXTURIZED ENAMEL. allowing 24 hours between coats.

Bare Wood. The surface should be clean, dry and well seasoned. If required apply a sealing coat of POLIGLASS VARNISH diluted 50% or more with THINNER 203. After 24 hours sandpaper and apply 2 coats of   POLYURETHANE TEXTURIZED ENAMEL allowing 24 hours between coats.
 

Previously painted wood. Proceed with a patch test on a small area of the coated surface to verify if the old paint is compatible and to make sure that the old coating is still in sound condition. If the old coating is in good conditions and of 2-pack polyurethane nature, apply then one coat of POLIFOND and let dry for 12-24 hours. Sandpaper and overcoat with 2 coats of  POLYURETHANE TEXTURIZED ENAMEL allowing 18-24 hours between coats.

In the case of loose or powdery paint or if not compatile it is recommended that the old paint should be removed completely down to bare wood and that application directions as described above for bare wood be followed.

Product Specification
CONVERTERS & COLOURANTS
POLYURETHANE TEXTURIZED ENAMEL
Binder type A
Poliurethane
Specific gravity kg/lt (±0,05)
1.360 (A) 1.000 (B)
Solids content (volume) ±2
56%
Shelf life (+10+30°C)
12 months in airtight cans
Mixing ratio A+B by weight
8 parts of Sol.A (Base+ Colourants) with 1 part Sol.B
Brush-Roller
2-5% Thinner 203 (Light textured enamel)
Dust dry
30-40 minutes (20c)
Application temperature
Between +10 C and +40 C
Dry film thickness advised
100 microns per mano
Colour mixing by weight
75 parts of Neutral Base with 25 parts of Colourants
Color code
4DNE00
Binder type B
Aliphatic Isocyanate
Solids content (weight) ±2
70%
Viscosity Ford ø 8 at 20°C ±2
Tixotropico
Application
Brush-Roller
Pot life A+B (20°C)
use within 4 hours
Spray
2-5% Thinner 203 (Light textured enamel)
Recoat time
24 h
Relevant humidity
Less than 80%
Theoret. coverage m2/Lt
3-4 m2/kg
Colors
NEUTRO