WHITEXT BUCCIATO

WHITEXT BUCCIATO

Semi-gloss textured white finish with excellent properties of flexibility and weather resistance in marine environment. Performs a non-yellowing "orange-peel" finish particularly recommended for topsides and superstructures of yachts and where it may be necessary to reduce surface uneveness or surface imperfections. For spray application a special spray equipment for “orange-peel” finish must be used. The “orange peel” grade can be adjusted by regulating the percentage of thinning (the higher the dilution and the smoother the orange peel effect ).
Brand : SKIPPER'S LINE MARINE PAINTS
Description
SURFACE PREPARATION AND APPLICATION PROCEDURE - Bare Steel - Onto sandblasted steel according to SA 2,5 apply two coats of EPOZINC 2C or EPOFOND AM-9. If sandblasting would not be possible degrease the surface and remove any trace of corrosion providing a suitable anchor pattern. Any loose paint should be meccanically removed. Apply 2 coats of EPOFOND AM-9 primer and let dry. Fill up if necessary with PLAMUR FINISHER MDF. Apply then one coat of POLIFOND primer, let dry for 24 hours and sandpaper. Overcoat with 2 coats of WHITEXT BUCCIATO allowing 18-24 hours between coats. Fibreglass - The surface to be coated should be degreased with suitable cleaner, rinsed and slightly sanded with fine abrasive paper. Remove dust and clean the surface. If the surface is slightly powdering it is necessary to apply one coat of POLIFIBER PRIMER allowing 18-24 hours between coats. Fill up if necessary with PLAMUR FINISHER MDF. Overcoat with 2 coats of WHITEXT BUCCIATO allowing 24 hours between coats. Bare Wood - The surface should be clean, dry and well seasoned. If required apply a sealing coat of POLIGLASS VARNISH diluted 50% or more with THINNER 203. After 24 hours sandpaper and apply 2 coats of WHITEXT BUCCIATO allowing 24 hours between coats. Previously painted wood - Proceed with a patch test on a small area of the coated surface to verify if the old paint is compatible and to make sure that the old coating is still in sound condition. If the old coating is in good conditions and of 2-pack polyurethane nature, apply then one coat of POLIFOND and let dry for 12-24 hours. Sandpaper and overcoat with 2 coats of WHITEXT BUCCIATO allowing 18-24 hours between coats. In the case of loose or powdery paint or if not compatile it is recommended that the old paint should be removed completely down to bare wood and that application directions as described above for bare wood be followed.
Product Specification
ENAMELS
WHITEXT BUCCIATO
Paint Type
Two components
Binder type B
Aliphatic Isocyanate
Specific gravity kg/lt (±0,05)
(A) 1.500 - (B) 0.980
Viscosity Ford ø 8 at 20°C ±2
Tixotropico
Viscosity Ford Ø4
Thixotropic
Mixing ratio A+B by volume
3 parts Sol.A with 1 Sol.B
Brush-Roller
5-10% Thinner 205 (smooth finish)
Dust dry
30-40 minutes (20c)
Application temperature
Between +10 C and +40 C
Dry film thickness advised
100 microns per coat
Colors
BIANCO
Binder type A
Poliurethane-polyester
Code & colour B
8Z903.Sol.B
Solids content (volume) ±2
40%
Shelf life (+10+30°C)
12 months in airtight cans
Application
Brush-Roller-Spray
Pot life A+B (20°C)
use within 6-8 hours
Spray
5-10% Thinner 203 (smooth finish)
Recoat time
24 h (20°c)
Relevant humidity
Less than 80%
Theoret. coverage m2/Lt
5-6
Color code
4P3902