ACRIGLASS

ACRIGLASS

Two-component polyacrilic enamel, absolutely non-yellowing, performing gloss retention properties and colour stability. Recommended for professional painting finIsh of yachts and boats. Applied over EPOFOND AM-9 epoxy primer provides a long lasting finish highly resistant to marine environment. Available in a wide range of colours (See colour card).
Brand : SKIPPER'S LINE MARINE PAINTS
Description
SURFACE PREPARATION AND APPLICATION PROCEDURE - Bare Steel - Onto sandblasted steel according to SA 2,5 – apply two coats of EPOZINC 2C. or EPOFOND AM-9 If sandblasting would not be possible degrease the surface and remove any trace of corrosion providing a suitable anchor pattern. Any loose paint sjhould be mechanically removed. Apply 2 coats of EPOFOND AM-9 primer and let dry. Fill up if necessari with PLAMUR FINISHER MDF. Apply then one coat of POLIFOND primer, let dry for 24 hours and sandpaper. Overcoat with 2 coats of ACRIGLASS ENAMEL allowing 24 hours between coats. Fibreglass - The surface to be coated should be degreased with suitable cleaner, rinsed and slightly sanded with fine abrasive paper. Remove dust and clean the surface. If the surface is slightly powdering it is necessary to sandpaper and apply one coat of POLIFIBER PRIMER allowing 18-24 hours between coats. Fill up if necessary with PLAMUR FINISHER MDF. Overcoat with 2 coats of ACRIGLASS ENAMEL allowing 24 hours between coats. Bare Wood - The surface should be clean, dry and well seasoned. If required apply a sealing coat of POLIGLASS VARNISH diluted 50-75% or more with THINNER 203. After 24 hours sandpaper and apply 2 coats of ACRIGLASS ENAMEL allowing 24 hours between coats. Previously Painted Wood - Proceed with a patch test on a small area of the coated surface to verify if the old paint is compatible and to make sure that the old coating is still in sound condition. If the old coating is in good conditions and of polyurethane nature, apply then one coat of POLIFOND and let dry for 12-24 hours. Sandpaper and overcoat with 2 coats of ACRIGLASS ENAMEL in the desired shade. In the case of loose or powdery paint or if not compatible it is recommended that the old paint should be removed completely down to bare wood and that application directions as described above for bare wood be followed.
Product Specification
ENAMELS
ACRIGLASS
Paint Type
Two components
Binder type B
Aliphatic Isocyanate
Specific gravity kg/lt (±0,05)
(A) 1.250-1.380 according to colour - (B) 1.045
Shelf life (+10+30°C)
12 months in airtight cans
Application
Brush-Roller-Spray
Pot life A+B (20°C)
use within 6-8 hours
Brush-Roller
15-25% Thinner 205
Dust dry
1-2 hours
Application temperature
Between +10 C and +40 C
Dry film thickness advised
40 microns per coat
Colors
Bianco, AZZURRO, BLU MARINO, BLU OCEANO, GIALLO CROMO, GRIGIO CHIARO, NERO, ROSSO VIVO, VERDE SMERALDO
Binder type A
Polyester acrylic
Code & colour B
8ZACRI.Sol.B
Solids content (volume) ±2
49%
Viscosity Ford Ø4
120-180 sec. (A+B)
Mixing ratio A+B by volume
3 parts Sol.A with 1 part Sol.B
Temperature Pot Life
20°C
Spray
20-35% Thinner 203
Recoat time
24 h (20°c)
Relevant humidity
Less than 80%
Theoret. coverage m2/Lt
10
Color code
2W0000, 2WA121, 2WA142, 2WA122, 2WA110, 2WA116, 2WA070, 2WA113, 2WA126