SERENISSIMA

SERENISSIMA

High quality, long lasting idrophilic matrix antifouling paint. The high content of coprous oxide and other valuable additives, combined to the particular vehicle formulation, allow this product to provide an excellent antifouling power in the most varied conditions. The hydropfilic nature of the vehicle improves wettability and flowing characteristics of the hull in the water. It can be effectively used also in warm seas and miscellaneous water. Provides a controlled speed release of the antifouling salts which makes this product recommended on both medium speed boats and sailing boats. Not suitable on aluminium boats. Recommended for boats with speed up to 30 knots.
Brand : SKIPPER'S LINE MARINE PAINTS
Description
SURFACE PREPARATION AND APPLICATION PROCEDURE - Bare Steel bottoms - Apply 1 coat of EPOZINC 2C or EPOFOND AM-9 on sandblasted steel according to SA 2,5/3 and let dry for 12-24 hours. (If sandblasting is not possible proceed with mechanical cleaning to bring the surface to bare steel, apply 1 coat of CROMOMINIO-AT and let dry for 8-12 hours.) Apply then 2 coats of SOLVER PRIMER allowing 24 hours between coats. Overcoat twith 2-3 coats of SERENISSIMA antifouling allowing min.8 hours between coats. Bare Wood - Apply one coat of EVIOX CROMOMINIO and allow to dry for 8-12 hours. Apply 2 coats of SOLVER PRIMER allowing 24 hours between coats followed by 2-3 coats of SERENISIMA antifouling allowing min. 8 hours between coats. Fibreglass - Degrease with detergent solution and rinse with water. Light sanding with fine abrasive paper and apply 1 coat of POLIFIBER PRIMER. Allow 24 hours before sandpapering with fine abrasive paper. Overcoat then with 2-3 coats of SERENISSIMA antifouling allowing min.8 hours between coats. Previously Coated Boat Bottoms - Apply 2 coats of SERENISSIMA after light sandpapering. Over old antifouling in good condition, a patch test on a small area is necessary to check the compatibility with the new antifouling. If this is okay, sandpaper with fine abrasive paper and apply 2 coats of SERENISSIMA. In case some tiny bubbles are experienced during the patch test, apply first one cot of SOLVER PRIMER in order to insultate the old layer of paint. Apply 2-3 coats of SERENISSIMA antifouling allowing min. 8 hours between coats. It is however recommended that every 3 or 4 years of repainting the old paint layers should be removed. *Note 1. Brush application. The antifouling should be applied by longitudinal movement with respect to waterline. Wait minimum 8 hours before applying the second coat. A third coat of SERENISSIMA should be applied on the waterline and on the rudder.
Product Specification
ANTIFOULINGS
SERENISSIMA
Paint Type
One component
Specific gravity kg/lt (±0,05)
1.650-1.780
Viscosity Ford ø 8 at 20°C ±2
12-15
Application
Brush-Roller-Spray
Spray
10-15% Thinner 400
Launching time
Min 24-48 hours
Application temperature
Between +10 C and +40 C
Dry film thickness advised
40-50 microns per coat
Colors
NERO, AZZURRO, BLU SCURO, ROSSO OX
Binder type A
Synthetic copolymer - Hydrogenated resin
Solids content (volume) ±2
38%
Shelf life (+10+30°C)
12 months in airtight cans
Brush-Roller
Ready to use or max 5% Thinner 400
Touch dry
1-2 h (20°c)
Recoat time
8-12 h (20°c)
Relevant humidity
Less than 80%
Theoret. coverage m2/Lt
8-10
Color code
3F5748, 3F5795, 3F0766, 3F5745